Calibre遇到的問題

dreamland

執行calibre時,出現了這個警告:
; _+ }1 m: I2 n3 ]

1 }, Y2 l3 j+ @+ [. q4 U. D" qCould not connect to socket 9189 on host localhost

Probable causes:
# |* s3 G+ S' w# ]" l: r, t2 z
; [- M6 M" h: |1: The viewer is not running, or
2: The viewer's server socket is not activated
1 \! T/ ?5 C! d& G

1 V5 m* U8 Q+ ~/ [請問有人遇過嗎?

shkao0201

那是因為你的layout tool的port不是使用9189
所以你無法將RVE的資料傳回layout
7 p8 J) H" @  j9 u1 Qvirtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
laker:Verify---Calibre---Integrate with RVE---Server Port--->9189

dreamland

原帖由 shkao0201 於 2009-10-29 05:51 PM 發表
那是因為你的layout tool的port不是使用9189
所以你無法將RVE的資料傳回layout
virtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
laker:Verify---Calibre---Integrate with RVE---Server Port--- ...

' F. ]$ B* l* Z4 d: p3 u, w
) _( o8 n) t8 x2 \2 F% ]( F' O
我使用的server port是9189

shkao0201

試試在Calibre RVE視窗中: Setup---Layout Viewer-----LayoutViewer(選other(Virtuoso))**Laker要選這個
, B* O! j) Y! J3 w, G                                                                                         ----IPC  settings--socket number-----9189

shkao0201

然後你可以試試點Connect是否會出現Success.

shkao0201

Setting Up Communication With a Viewer
If you invoke Calibre Interactive from a layout or schematic viewer, communication between
the two applications is set up automatically. If you open a viewer after invoking Calibre
+ ^2 w/ `, h8 t+ E9 {7 aInteractive, you can set up communication between the two tools through IPC sockets.
( K8 V6 f0 c8 YBy default, Calibre seeks socket 8192, and if that socket is available, connection is automatic.
( J/ `+ r( F/ t: M2 j# QYou can change the socket address used by following this procedure:
) h( K6 _4 E# P& Y$ ^6 x; O% J1. Open the viewer.
2. Activate a socket following the instructions described in the user manual for the layout viewer you have opened.
6 c& i4 U5 H9 v7 z7 n  a3. In Calibre Interactive, choose Setup > Layout Viewer…
9 W, `8 I& |; D# S, s: M' v7 n) g4. Enter the socket number that you activated in the viewer.
+ Q. i( Q3 I% _5. Click Connect.
) y# f: C! C9 ~  ~6. Click OK. The figure shows setup of a layout viewer.

dreamland

原帖由 shkao0201 於 2009-10-29 06:12 PM 發表
Setting Up Communication With a Viewer
1 q+ E# L3 K' I# `, h: @0 k# sIf you invoke Calibre Interactive from a layout or schematic viewer, communication between
the two applications is set up automatically. If you open a viewer a ...

4 y/ y* h9 N% o% y  \9 a一樣不行用?

shkao0201

你是試用laker去叫出RVE呢??
它的socket number 有相同嗎?