Calibre遇到的問題

dreamland

執行calibre時,出現了這個警告:
7 c: ?$ E  v- ~
6 G; j. ?$ i: B% o
4 z1 s4 B- C: h4 R1 k4 \Could not connect to socket 9189 on host localhost
% |! v2 i5 v- Z* R
) e4 U* p: n3 D+ nProbable causes:

; m: H" H6 \+ E% H0 h4 f% C' j1: The viewer is not running, or
2: The viewer's server socket is not activated
# t1 L- c* t& w, D; j
; i2 W. ]8 l7 u8 ^
0 R' c$ Y1 ^3 [% n% w: n; H請問有人遇過嗎?

shkao0201

那是因為你的layout tool的port不是使用9189
% ]/ [7 S% ]5 J# @: k( d0 ]: g所以你無法將RVE的資料傳回layout
( I, ^  ~. G2 r; \( H3 r5 uvirtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
, Y5 Z; n) ?7 w+ Tlaker:Verify---Calibre---Integrate with RVE---Server Port--->9189

dreamland

原帖由 shkao0201 於 2009-10-29 05:51 PM 發表
0 d; D" Q; o  ?8 ~那是因為你的layout tool的port不是使用9189
所以你無法將RVE的資料傳回layout
3 V$ k1 d! S3 P& n8 I8 B- G& |! vvirtuoso:  Calibre---Setup---Socket-----Socket Number---->9189
& H/ n1 ~" b/ z* nlaker:Verify---Calibre---Integrate with RVE---Server Port--- ...

我使用的server port是9189

shkao0201

試試在Calibre RVE視窗中: Setup---Layout Viewer-----LayoutViewer(選other(Virtuoso))**Laker要選這個
( y3 M- M. [/ G                                                                                         ----IPC  settings--socket number-----9189

shkao0201

然後你可以試試點Connect是否會出現Success.

shkao0201

Setting Up Communication With a Viewer
If you invoke Calibre Interactive from a layout or schematic viewer, communication between
the two applications is set up automatically. If you open a viewer after invoking Calibre
Interactive, you can set up communication between the two tools through IPC sockets.
By default, Calibre seeks socket 8192, and if that socket is available, connection is automatic.
You can change the socket address used by following this procedure:
1. Open the viewer.
5 `) _) I  ]* a( a  a' p8 `* D2. Activate a socket following the instructions described in the user manual for the layout viewer you have opened.
  \7 N, m* C) a2 X7 T: q7 g3. In Calibre Interactive, choose Setup > Layout Viewer…
3 X; P) Y& ?0 a8 N4. Enter the socket number that you activated in the viewer.
5. Click Connect.
2 `- e+ q" g. U- ~' ?/ A6. Click OK. The figure shows setup of a layout viewer.

dreamland

原帖由 shkao0201 於 2009-10-29 06:12 PM 發表
Setting Up Communication With a Viewer
, M% o( d: ]8 K( WIf you invoke Calibre Interactive from a layout or schematic viewer, communication between
the two applications is set up automatically. If you open a viewer a ...

一樣不行用?

shkao0201

你是試用laker去叫出RVE呢??
) p1 A1 [+ b7 F( }5 |- I它的socket number 有相同嗎?