初學者一問......有關EPM7128S......VCCINT & VCCIO的問題

jimcooper

請問一下VCCINT & VCCIO還有其對應的GND 這些腳位是做甚麼用的啊??
! B$ {# g0 r2 V! `+ F5 g
我已經看我DATASHEET上對這方面的說明,但感覺還是有點不清楚
感覺上VCCINT & VCCIO好像只需要各接一隻腳就可以了,其他相同名稱的腳位都是相通的.....
  v+ [; m6 E8 p% A! ~* S# R- ?我的想法正確嗎??

' W) N8 b& F! q- {如果布正確的話....
能麻煩各位幫我做個詳細的解說嗎??
3 G8 S3 d8 k2 v5 E& m1 U
先說聲謝謝~
8 x) m* [1 M* o% Q) j
7 O  D$ m$ i2 v/ g) O

2 t$ {7 G% e  v6 U( T----------以下是DATASHEET針對VCCIO & VCCINT所做的說明------------

MultiVolt I/O Interface

MAX 7000 devices—except 44-pin devices—support the MultiVolt I/O
interface feature, which allows MAX 7000 devices to interface with
. X" i& k8 l& A) Ysystems that have differing supply voltages. The 5.0-V devices in all
packages can be set for 3.3-V or 5.0-V I/O pin operation. These devices
have one set of VCC pins for internal operation and input buffers
(VCCINT), and another set for I/O output drivers (VCCIO).
5 h: ^( ~& ~( ^  }- _& G( pThe VCCINT pins must always be connected to a 5.0-V power supply.
; A" k) I! Z3 {/ F+ mWith a 5.0-V VCCINT level, input voltage thresholds are at TTL levels, and
are therefore compatible with both 3.3-V and 5.0-V inputs.
0 q' B1 ^: X) U; AThe VCCIO pins can be connected to either a 3.3-V or a 5.0-V power
supply, depending on the output requirements. When the VCCIO pins are
1 r: z0 j0 d1 uconnected to a 5.0-V supply, the output levels are compatible with 5.0-V
+ Z+ f/ K$ w# g% |$ A% z! p6 M5 Lsystems. When VCCIO is connected to a 3.3-V supply, the output high is
3.3 V and is therefore compatible with 3.3-V or 5.0-V systems. Devices
operating with VCCIO levels lower than 4.75 V incur a nominally greater
timing delay of tOD2 instead of tOD1.
$ ?$ p: f) s7 S* e" q" w7 }3 ^
; P/ w8 H7 O5 |6 }! [[ 本帖最後由 jimcooper 於 2008-11-9 04:21 PM 編輯 ]

sieg70

Vccint跟Vccio, 以及Ground"每根"都要接

addn

您好
VCCINT接5v,則當io pin為輸入時,可接受3.3v,5v的輸入準位
VCCIO接5v/3.3v,則當io pin為輸出時,輸出準位就為5v/3.3v準為位

[ 本帖最後由 addn 於 2008-11-10 10:16 AM 編輯 ]

ssejack1

VCCIO 在有些產品有分 block, 當不同 IO 電壓要使用在同一顆 IC 時可以劃分在不同的 block 就可同時使用不同之IO 準位; VCCINT 為 IC core 電壓,與 user 較沒直接關係,只要依 spec. 供給就沒有問題!
. }& X0 B( k  F9 I" y- P* @3 `須注意的是 VCCINT 與 VCCIO 有點影響,越低的 VCCINT 製程越新, delay / speed 多比較快,壞處是 VCCIO 會較低;
# l* j( \4 f  f% f1 a" c比如 VCCINT = 3.3V者, VCCIO 一般 3.3/5.0 均可,但 VCCINT = 2.5者 VCCIO 或許無法始用 5.0 v 了!
  n3 Z4 @5 G  `, a0 a參考參考!